herve leger toronto rcp pxu qlpb shx

[v5440479]

,herve leger toronto
Asphalt membrane roofing detail structure treatment


Deal by Lantian E 1-water layer structure: 2-linoleum, three, a handful of steam road} 4-3 exhaust fine aggregate concrete structure treatment exhaust hole detail roof exhaust holes within 36m of each set by one, row water vapor hole must be prepared to deal with,vibram five fingers outlet, to prevent leakage. Exhaust hole handle detailed structure shown in Figure 2. 4 parapet flashing deal with problems detailed structure of salt small u, (as Fan Fuqing Waterproof Decorative 1 - Process Company) 2 exhaust holes detailed structural waterproofing treatment l a: 2 a waterproof ointment: 3 an exhaust pipe brick masonry parapet should be full when the mortar, plaster should be done when the water pick brick slope above, under the port must be prepared at the drip line of the pan of water should be added an additional waterproof layer. Parapet flashing process a detailed structure, fy0%: 3-faced parapet removal treatment technique dig small E 1-2 is an additional waterproof layer waterproof layer 5 parapet outlet near the outlet of the detail structure treatment of depression should be made slightly lower pit, to ensure smooth flow of water. Outlet should be made around the sun angle obtuse angle, an additional waterproof layer and waterproof layer should be inserted into the outlet inside. Parapet wall outlet detailed structure processing shown in Figure 4. Figure 4 parapet outlet structure treatment depression l-fine layer of water is an additional waterproof layer # 2 male 226 = 2, building technology pedicle f1 Volume 22) c ~] roof construction quality control and supervision of pre-Qiaoshuang Wang (Taiyuan Construction Quality Supervision Station,Beats By Dre Headphones, 030002) 1U7f ---. 'J a, Taiyuan Yifen Ministry of Housing Court is one pilot area, to ensure that community groups as priority projects. In the roof construction, we have taken a series of quality measures for prevention and control and supervision, with good results, and by users. 1 General Requirements (1) roofing felt four works by three oil water practices. (2) roofing projects must be waterproof or water-proof professional team of construction workers. And should be trained before induction. (3) Community All roofing projects must be made exhaust roof layer 2 security ju (1) selection of the slag particle size of ~ lOmm do insulation layer, particles with a certain strength should not be used without burning the coal and coal waste through pre-construction to sift, to weed out the excess flour Su (2) roof drainage slope of 2. Appropriate, but not> 3. Copy before laying flat gray cake to find slope, in order to ensure proper drainage slope roof. (3) control the slag virtual height and compression ratio, set the scale,knock off oakleys, playing the line, marked the virtual shop and compacted thickness. Bomb line construction in strict accordance with the ruler. (4), furnace insulation layer of 8:1 cement cancer. Must Mixer and then on top of paving. Not on the roof with the artificial mixed with the shop, pay attention to controlling moisture content. (5) when the insulation material cornice to cornice to shop,diesel store paris, to avoid the exposed concrete, causing cracks in the top floor temperature. 3 pull leveling r <1) shall not use expired cement kiln production of cement and small applications, coarse sand, no sand. More are not allowed to use silt. (2) strictly control the ratio and water-cement ratio, cement mortar consistency should not be greater than 3.5era. (3) layer of cement mortar before the final setting should be some light pressure, usually 1 ~ 3h, but not too light weight (if weight is too light, will not help the linoleum with knot revolves screed due to the cement mortar layer pores have all been closed, is not conducive to ventilation). Cable should not increase cement slurry pressure light (cement slurry and cement mortar shrinkage values ​​are significant differences between easily lead to hollowing crack). (4) screed to indwelling sub-lattice seam, Ke from less than 6m. Seam depth and width of 20ram, with m determined formers (removed before the final setting of cement mortar). 4 linoleum waterproof layer (1) selection of material standards in line with linoleum, and by the quality supervision departments have agreed to before using (2) Mastic degree of heat subject to stringent testing, the label should be required to use (3) cold-base oil brushing to be thin and uniform, not tainted brush blank rejection point and the bubble. Brushing should be in the shop before the 1 ~ 2d be felt. The reservoir dry and without dust. (4) felt the paving in order to determine the basis for roof drainage slope perpendicular to the slope paving, Xianpu additional layer. Omo felt after the shop, not up and down two perpendicular paving operation. L group of 3 people, one in the former asphalt pot evenly sprinkle with oil, and one followed Laying linoleum, linoleum flattened shall compaction, paving work followed by 1, the side of the oil in time to shop 6 detailed structure of the roof pipe processing pipe piercing the roof, there are many, if not handled properly these areas most likely to produce bleeding mattress, so there must be proud of a good deal of water pipeline construction deal with a roof detail shown in Figure 5. Figure 5 details a roof construction pipeline processing} 2 l anti-ball is an additional layer of waterproof layer 7 at the door opening Exalted roof detail roof construction process at the Master El openings, to do first after the water puzzle still, should also add an additional waterproof layer . El roof openings at the detailed structure Exalted processing shown in Figure 6. Figure 6 on the roof where the door handle detailed structure Si-mouth 1-l2 additional waterproof layer of waterproof layer
More articles related to topics：


air jordan high heels des urv ttsk rfd

Oakley sunglasses sale kpn qxx ojjn glt