p90x workout schedule PVC plastic floor surface co

[v7312937]

PVC plastic floor surface construction technology


On, the pressure will lead to bubble formation. Construction with a soft wood or hard board wrapped in blankets, and carefully squeeze has spread on the ground, then rolled with the roller to eliminate air bubbles. After laying flooring if cross, the joint can be cut to size. If there is residual glue joints, immediately with water, cotton cloth or scrub erased. Coil indirect seam welding connection method using heat, the law firm seams, waterproof and health, Sweden Forbo welding electrode, made from PVC material, the melting point of plastic flooring with Forbo same system-specific accessory products, heat welding should be to be completely bonded with the adhesive material after (that day). Side seams must be dense, because the interface gap is too much effect on the quality of welding, notch depth to thickness must be 2 / 3, to ensure the welding strength and adhesion. Grooves must be clean, slotted knife hand end. Welding should be used to ensure proper temperature and equipped with professional high quality 5mm caliber gun fast gun nozzle, torch preheat temperature exposure. To partition a large area of ​​construction operations, and maintained at 350 - 450 ~ C, to melt the surface material - a + a + a + a + a + a + a + a + a + a + a + a + a + a + a + a + a + an + and electrode temperature. More than half of the required length of rod into the gun mouth, pressed into the open section of the tank after 1min,mbt shoes ireland, and then further moves heat gun, melt rate control electrode, welding rod ends need to form a small bead-like. Electrode is not fully cooled down, the repair with a crescent knife and scissors cut off the excess part of the other side of the central repeat the above steps to be welded junction should overlap 2mm, until completely cooled electrode for final finishing. 8 Quality Inspection (1) polished surface after cleaning, before brushing interface agent. (2) self-leveling cement floor construction is completed shall be subject to inspection and approval before entering the next process of construction. (3) surface layer and the next layer of paste should be firm,mac cosmetics wholesale, not Alice corner material, not unglued, no excess glue, no damage, no blistering. (4) surface roughness with 2m by foot and wedge feeler, to allow deviation is less than 2mill. 5m grid straight seam line and pull the steel ruler inspection, surface flatness deviation is less than 3mill, joints poor tolerance level is not greater than 0.5mm. Board surface should be clean, clear pattern, color consistency, tight joints, beautiful, patchwork at the pattern, pattern match, no glue marks, and the transfer of the wall closely, Founder of yin and yang side angle collection. (5) plate welds should be smooth, clean, non-coking discoloration, spots, welding defects such as tumors and from the scales, allowing the bump to ± 0.6mill, bending strength of the weld strength of not less than 75% of plastic sheeting. (6) has laid the ground clearance, subject to a period of time before use. Not new ground for the laying of other operations, the total package together to be protected with a new shop on the ground. A - a - a - a - a + a + a + a + a + a + a +03 J601-2 ((wood windows and doors parts Integrated) window cover windows and doors fan, instead of the traditional door frames, with holes set of National Building Standard Design Atlas,ghd planchas, by the Chinese construction bonding without nails fixed, fast and convenient, time than the hand-decorated line Door trim panel, 45 degrees to the standard design building the Institute and Shandong FIRST installed on-site production reduced by 50% or more. 90 degree angle-and top-two forms together. decoration Co., Ltd. jointly developed, has been officially published (1) doors ( including doors, windows, door pockets and accessories (2) wood for the sliding window, including glass inlay whole issue. line). glass sliding windows, inlaid wood lattice 1 using the entire range of glass sliding doors and sliding doors into two Swing large and even the sliding doors in this atlas for hotels,p90x workout schedule, guesthouses, office class. swing gate, including plywood doors, parquet plywood door, window cover, including a single three-wire type window cover, a single four-room, high-end residential and other various class building convinces one hundred plywood doors, flat panel doors, wood paneling type window cover, and double four sets of linear sliding doors with a similar push with the environment inside the doors and windows doors, mixed panel doors, glass doors set the whole , pull the window cover glass inlay and a half 2 Atlas content glass doors, inlaid side of the glass door, decorative wood lattice glazed door trim line and the same parts Integrated Health wooden windows and doors factory gate, Iron inlaid glass doors . sliding glass doors, including the entire set, including wooden doors and windows used Atlas table, doors and windows set production, all the parts according to standardized sets of doors and windows fan, series glass sliding doors and wood lattice glazed sliding doors. into a size relationship map, windows and doors node detail, door of the pre-, in the field directly in the hole, including the installation of door Door Swing sets, sliding door pocket and door and window details and parts of the node sets of sections.
More articles related to topics：


abercrombie ireland 95 to write a master thesis network

tory burch outlet Tic-Tac security guards stand improvement

tory burch outlet Network 713 to write a master thesis